IS 5496 : 1993 ( Reaffirmed 2003 ) GUIDE FOR PRELIMINARY DIMENSIONING AND LAYOUT OF ELBOW TYPE DRAFT TUBES FOR SURFACE HYDROELECTRIC POWER STATIONS ( First Revision ) UDC 627'85 : 621'224-225'14 Q BIS 1993 BUREAU MANAK OF INDIAN 9 BAHADUR DELHI STANDARDS SHAH ZAPAR MARG BHAVAN, NEW 110002 Price Group 2 September 1993 Hydraulic Power House Structures Sectional Committee, RVD 15 FOREWORD This Indian Standard was adopted by the Bureau of Indian Standards, after the draft finalized by the Hydroelectric Power House Structures Sectional Committee had been approved by the River Valley Division Council. The draft tube of a reaction turbine is the conduit connecting the exit from the runner to the tail race, thus having the function of utilizing the differential elevation between the runner exit and the tail water level, termed as static suction head, recovering as much as possible of the velocity Draft tubes may be one of the following types: head in water leaving the runner. a) Straight b) Hydraulic conical draft tube; moody type which may be: cone type draft tube, for example, 1) High cone; 2) low cone; and c) Elbow type draft tube. NOTE The types given at (a) and (b) are normally used for very small units. This standard is intended for fixing up the preliminary overall dimensions of elbow type draft tubes for the purpose of incorporating them in the project design ( layout of the power house ) when the It also gives general guidance for design of the draft tube is not available from the manufacturers. the design of the elbow type draft tubes. This standard was first published in 1969. The present revision has been made in view of the The following changes experience gained during the course of these years in use of this standard. have been incorporated in the first revision: 1) The width of each pier is recommended as 1 000 mm. 2) Draft tube design type 3 has been deleted. 3) Depth of Kaplan & Francis turbine recommended has been increased. For the purpose of deciding whether a particular requirement of this standard is complied with, the final value, observed or calculated, expressing the result of a test or analysis, shall be rounded off in accordance with IS 2 : 1960 `Rules for rounding off numerical values ( revised )`. The number of significant places retained in the rounded off value should be the same as that of the specified value in this standard. IS 5496 : 1993 Indian Standard GUIDE FOR PRELIMINARY DIMENSIONING AND LAYOUT OF ELBOW TYPE DRAFT TUBES FOR SURFACE HYDROELECTRIC POWER STATIONS ( First Re vision ) 1 SCOPE This standard covers the criteria for the selection of various dimensions of elbow type draft tubes for hydroelectric power stations. 2 REFERENCES The Indian Standards listed adjuncts to this standard: IS No. 226 : 1985 2062 : 198j 3 HYDRAULIC below are necessary Title Structural steel (standard (fifth revision ) Weldable revision ) structural quality ) 3.5.1 The outlet end of the draft tube should be so located that it remains submerged under all operating conditions of the unit at least by Vc2/2g or 30 cm whichever is greater, where V, is the exit velocity and g is the acceleration due to gravity. The slope of excavation connecting the draft tube floor at exit and bottom of the tail race should not be steeper than one vertical to four horizontal. 3.5.2 The height of the draft tube at exit is normally recommended as 0'94 D to 1'32 D ( D being the inlet diameter of the runner) depending upon the specific speed of the turbine; the lower value being for lower specific speeds. 3.6 Depth of the draft tube is reckoned centre line of the guide apparatus. from the 3.5 For the inlet cone of the elbow type draft tubes, the half angle of conicity recommended is 6" to 10". A bed slope of about one vertical to ten horizontal is recommended. However, a slope of one vertical to six horizontal is the steepest slope which should be permitted. steel ( third DESIGN CRITERIA 3.1 The dimensions of the draft tube depend on the specific speed, size and spacing of the unit and is mainly governed by the diameter of the runner. 3.2 The design should be such that the total losses in the draft tube and exit losses should be minimum possible economically. The deceleration should be gradual and so that transition should be gradual with smooth surfaces. 3.3 One or two intermediate piers in the draft tube leg may be provided to give structural support and also to reduce the span of the draft tube gates which are required for dewatering of the draft tube. Piers should be well streamlined so that they are efficient hydraulically. The number of piers depends upon structural considerations, however, it is recommended that no pier should be provided with span up to 7 m; one pier should be provided for span from 8 m to 15 m and two piers should be provided for span more than 16 m. For span? between 7 m and 8 m and 15 m and 16 m, this choice is left to the discretion of the designer. The minimum width of each pier should be as l 000 mm sufficient to accommodate the draft tube gate grooves. 3.4 Preliminary design of draft tubes may be made by referring to either of the Fig. 1 and 2 in accordance with the values of H, L and B given in 3.5, 3.6, 3.7 and 3.8 respectively. NOTE - The dimensions eiven in 3.5. 3.6. 3.7 and 3.8 are only for preliminary d&sign. The &naI `dimensions should, however, be taken as supplied by the turbine manufacturers. 3.6.1 For Kaplan turbines normally a depth of 2'3 to 3'0 D is recommended depending upon specific speed of the turbine. For Francis turbine a depth of 2'5 to 3'3 D is recommended. This may vary to a certain extent depending upon factors enumerated in 3.1. 3.7 The length of the draft tube, measured the turbine axis, is normally recommended to 5 times the runner inlet diameter. from as 4 3.8 The basic width ( excluding the pier ) of the draft tube exit is normally recommended as 2.6 to 3'3 D. In exceptional cases it may be even higher or lower. 3.9 For better block arrangement, draft tubes are sometimes made eccentric with respect to the unit centre line in plan. The value of the eccentricity should be limited so as not to adversely affect the hydraulic characteristics of the turbine. 4 MATERIAL 4.1 Draft tubes required strength 1 should be made of R.C.C. with necessary reinforcement. of IS 5496:1993 _ d OF GUIDE_ APPARATUS H = L = B = Depth of the draft tube Length Width of the draft tube of the draft tube FIG. 1 DRAFT TUBE DESIGN TYPE I ( FOR HEADS UP TO 200-250 m ) _-__.-_ ______ B OFGUIDE --_-_- APPARATUS OBLONGED SECTIONS IN ELBOW PORTION H = L - Depth of the draft tube Length of the draft tube B = Width of the draft tube FIG. 2 DRAFT TUBE DEXGN TYPE 2 ( FOR HEADS ABOVE 200-250 m ) 2 IS 5496: 1993 4.2 Steel plate draft liners should be provided in ihe tube to overcome the effects of erosion and pitting due to cavitation, if it exists. liner should extend to a point where the concrete can withstand the existing water velocities. This depends on the quality of concrete and its surface smoothness. 4.2.1 The that no liner should be provided for water velocities up to 6 m/s. Besides this consideration of velocity of water in the draft tube, it is recommended that liner should be provided in the cone of the draft tube. However, many times, due to the complicated shape of the elbow a liner may have to be provided in that portion also on the basis of the techno-economic calculations. NOTE - In certain cases velocities up to 8 m/s have been permitted without the provision of a liner. 4.2.1.1 It is recommended vided. The dimensions of the access should be adequate for a man to get in freely with provision to let down a ladder. The door of the access should be of steel and of enough thickness to withstand the pressures aed impact of water. The door should be weli fastened with rubber gasket packing all round to ensure water and air tightness. The door should be provided in the vertical portion of the draft tube. These openings should be connected to an access gallery running downstream or upstream or by the side of the unit. 7.1.1 In case where, because of hea.vy silt load in the water passing through the turbine, frequent repair/change of runner is envisaged, arrangement for removal of the runner through an opening provided in the draft-tube cone, should be made. The opening should be adequate enough to pass the runner through it. A steel door should be provided at the opening. The door should be well fastened with rubber gaskets all around to ensure air and water tightness. The openings provided for runner removal should be aproachable through access galleries of adequate size. These galleries may be provided with rails to take out the runners on specially designed trolleys. 5 MODEL TESTING 5.1 The model of the draft tube should be made along with the model of runner and tested along with it under all conditions of working of the machine.. 6 ARRANGEMENTS FOR DEPRESSING WATER LEVEL INSIDE DRAFT TUBE 6.1 In case where the generator coupled with the turbine is to be operated as a rynchronous condenser, arrangements should be made to depress the water level in the draft tube by means of compressed air. This is accomplished by admitting compressed air to the runner chamber subsequent to the closing of the wicket gates (guide vanes ). Compressed air should be admitted through a pipe and an opening check valve should be provided in the air in take pipe. The check valve should be sufficiently air-tight against the pressure in the runner chamber to prevent leakage. 7 ACCESS TO THE DRAFT TUBE and maintenance of the runner and for the upkeep of the draft tube an easy access to the draft tube should be pro7.1 For facilitating erection 8 DRAFT TUBE GATES Bulk head gates should be provided to close the draft tube against tailwater pressure during the maintenance period. The gate should be designed to carry the maximum tailwater pressure conditions. Suitable gantry with necessary operating platform should be provided for operation of the gates. 9 DRAINAGE BOX FOR DEWATERING DRAFT TUBE To facilitate dewatering of draft tube a drainage box should be fixed at the lowest point of the draft tube. The drainage box should then be connected to the power house sump directly or through a pipe system passing through a drainage gallery. Standard Mark The use of the Standard Mark is governed by the provisions of the Bureau of Indian Standards Act. 1986 and the Rules and Regulations made thereunder. The Standard Mark on products covered by an Indian Standard conveys the assurance that they have been produced to comply with the requirements of that standard under a well defined system of inspection, testing and quality control which is devised and supervised by BIS and operated by the producer. Standard marked products are also continuously checked by BIS for conformity to that standard as a further safeguard. Details of conditions under which a licence for the use of the Standard Mark may be granted to manufacturers or producers may be obtained from the Bureau of Indian Standards. Bureau of Indian Standards BIS is a statutory institution established under the Bureau harmonious development of the activities of standardization, and attending 10 connected matters in the country. Copyright qf Indian Standards Act, I986 to promote marking and quality certification of goods No part of these publications may be reproduced in BIS has the copyright of all its publications. the free use, in the any form without the prior permission in writing of BIS. This does not preclude such as symbols and sizes, type or grade course of implementing the standard, of necessary details, designations. Enquiries relating to copyright be addressed to the Director ( Publications ), BIS. Review of Indian Standards Amendments are issued to standards as the need arises on the basis of comments. Standards are also reviewed periodically; a standard along with amendments is reaffirmed when such review indicates that no changes are needed; if the review indicates that changes are needed, it is taken up for revision. Users of Indian Standards should ascertain that they are in possession of the latest amendments or edition by referring to the latest issue of `BIS Handbook' and `Standards Monthly Additions'. Comments on this Jndian Standard may be setit to BIS giving the following reference: Doc:No. RVD 15 (28) Amendments Amend No. Issued Since Publication Date of Issue Text Affected - BUREAU Headquarters: Manak Bhavan, 9 Bahadur Shah Zafar Telephones : 331 01 31, 331 13 75 OF INDIAN STANDARDS Marg, New Delhi 110002 Telegrams : Manaksanstha ( Common to all Offices ) Telephone Regional Central Offices: : Manak Bhavan, 9 Bahadur NEW DELHI 110002 Shah Zafar Marg 331 01 31 I 331 13 75 Maniktola 37 84 99, I 37 86 26, 53 38 43, 1 53 23 84 235 02 16, { 235 15 19, 632 92 95, t 632 78 91, 37 85 61 37 86 62 53 16 40 235 04 42 235 23 15 632 78 58 632 78 92 Eastern : l/14 C. I. T. Scheme VII M, V. I. P. Road, CALCUTTA 700054 : SC0 445-446, : C. I. T. Campus, Sector 35-C. CHANDIGARH IV Cross Road, Marol, MADRAS Andheri Northern Southern Western 160036 600113 : Manakalaya, E9 MIDC, BOMBAY 400093 ( East ) Branches : AHMADABAD. BANGALORE. BHOPAL. BHUBANBSHWAR. COIMBATORE. FARIDABAD. GHAZIABAD. GUWAHATI. HYDERABAD. JAIPUR. KANPUR. LUCKNOW. PATNA. THIRUVANANTHAPURAM. Printed at Printrade, New Delhi, India AMENDMENT NO. 1 MARCH 2001 TO IS 5496:1993 GUIDE FOR PRELIMINARY DIMENSIONING AND LAYOUT OF ELBOW TYPE DRAFT TUBES FOR SURFACE HYDROELECTRIC POWER STATIONS (FimtRevMm) (Page 1, clause 2, References ) -- Substitute tbe following for the existing matttx The Indian Standard IS 2062:1992 `Steel for General structural purpose' ( Supemeding IS 226 ) is a necessary adjunct to this standard. (WRD15) RqWI@IY Uniq BIS, NewtkllIL India